drew03cmc Posted April 17, 2007 Posted April 17, 2007 Hello, I just came back from tearing up the bluegill, bass and crappie here and noticed a chip in the paint on my IM6 graphite rod and am wondering if that will adversely affect the way the rod performs. I was throwing streamers for these fish, and bear in mind, there are some 5+# bass in this pond. Thank you in advance for helping me out here! Andy
Crippled Caddis Posted April 18, 2007 Posted April 18, 2007 Examine it under a strong light and magnification. If ONLY the paint is affected and there has been no damage to the graphite/epoxy matrix it should be fine. "You need only reflect that one of the best ways to get yourself a reputation as a dangerous citizen these days is to go about repeating the very phrases which our founding fathers used in their struggle for independence." ---Charles Austin Beard
jdmidwest Posted April 18, 2007 Posted April 18, 2007 I agree with CC, if it is only in the outer layer of finish, you should be fine. If it cracked the fibers in the graphite, it will create a weak point for a future break. If you are seeing the colored part broken it may be the graphite as the rods are usually clear coated, not painted. Look at it closer under magnification to determine how bad it is. "Life has become immeasurably better since I have been forced to stop taking it seriously." — Hunter S. Thompson
drew03cmc Posted April 18, 2007 Author Posted April 18, 2007 I will examine it right now...and, the verdict is...it is just the finish. Is there anything I can put on that to keep it from worsening? nail polish, super glue, what is a possibility? Andy
Crippled Caddis Posted April 18, 2007 Posted April 18, 2007 <I will examine it right now...and, the verdict is...it is just the finish. Is there anything I can put on that to keep it from worsening? nail polish, super glue, what is a possibility?> I think the real question should be, "What is compatable with the original finish". Only the manufacturer can tell you that. However-----and don't take this to the bank----I haven't yet seen superglue have an effect on painted finishes, but gamble on your own responsibility. "You need only reflect that one of the best ways to get yourself a reputation as a dangerous citizen these days is to go about repeating the very phrases which our founding fathers used in their struggle for independence." ---Charles Austin Beard
jdmidwest Posted April 18, 2007 Posted April 18, 2007 Probably a dab of clear nail polish like Sally Hanson Hard as Nails which I use for head cement also. If you do not have any flex coat finish laying around. Super glue could act as a solvent and react with the finish leaving a dull or white spot. Or you could just leave it alone and admire it as a battle scar. "Life has become immeasurably better since I have been forced to stop taking it seriously." — Hunter S. Thompson
Terry Beeson Posted April 18, 2007 Posted April 18, 2007 I would be a bit careful on what I use. Some depends on where it is. If it is a spot that has a lot of flex, superglue or Sally Hansen (which I use for head cement as well) may just crack after several casts. I would take it to a pro rod repair type person or at least get some advice from them before using any "home remedies" especially if the rod has any value. Speaking of which, you didn't mention what brand or if it was a "home built" from a blank. If it happens to be a Dorber blank, I'd be willig to bet they folks in Flippin would be glad to share a repair remedy with you. TIGHT LINES, YA'LL "There he stands, draped in more equipment than a telephone lineman, trying to outwit an organism with a brain no bigger than a breadcrumb, and getting licked in the process." - Paul O’Neil
drew03cmc Posted April 19, 2007 Author Posted April 19, 2007 No it is an IM6 graphite Redington (I bought another after selling one) Crosswater rod. It is the butt section of the rod, therefore not flexing much if at all. I used a dab of nail hardener and it appears to have somewhat worked. If it does not work, I guess I will have to get my fiberglass outfit sooner that I had thought I would! So, yes, that is all it is. Thanks guys! Andy
Kicknbass Posted April 19, 2007 Posted April 19, 2007 Have you thought about a fiberglass repair kit for a boat or tub/shower. I would think the resin would be similar. " Too many hobbies to work" - "Must work to eat and play"
drew03cmc Posted April 19, 2007 Author Posted April 19, 2007 Have not thought of that, good idea though...will give it some thought! Thanks. Andy
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now